8/12/2023 0 Comments Build a reamp boxUnbalanced cables have only two conductors and balanced have three conductors with an isolated ground loop which makes them less susceptible to RF interference. Some problemsīalanced and unbalanced signals differ in the number of conductors that carry the sound. You just need a bit of ingenuity to overcome some problems that might occur while you try to reamp a guitar without a reamp box. Of course, using a dedicated reamp box although very useful and convenient isn’t really necessary, it’s just one of those things that makes your life easier, but there’re other ways of achieving your goal. To simply put it, this is your best and the most reliable option to reamp a guitar and there’re plenty of very decent reamp boxes available on the market, but what should you do if your budget doesn’t allow it or if you’re simply in a hurry? Reamping a guitar without a reamp box ![]() ![]() Connect the output to the balanced input of your reamp box and send the unbalanced output to your amp. To reamp the guitar with a reamp box, you should send the DI guitar signal from your DAW to one of the DI outputs in your audio interface. Then it’s a matter of a very simple routing in your DAW. If you wish to record both a DI guitar signal and the amp, you need to connect your guitar directly into a reamp box, then send unbalanced output from the reamp box to the amp and balanced to your audio interface. The more advanced models let you split the signal and record both an amp and the direct input of the guitar. This basically means that reamp boxes serve to make guitar amps react to line-level signals as if it was directly connected guitar signal. ![]() Reamp box is a device that is used for converting a balanced line-level signal to an unbalanced high-impedance signal and vice versa. And the easiest way of reamping the guitar without a reamp box is to use digital amp emulation. Reamping is also possible if you manage to get your hands on a guitar amplifier with balanced inputs. U sing an older audio interface is far from ideal but still possible with the addition of a DIY or factory-made DI box. If you’re an owner of a recent audio interface, you can use an unbalanced output but you would need a splitter or a guitar pedal with multiple outputs in order to record guitar in the first place. The reamps are on the right.How To Mix A Song | Mixing Guitars | Part 5 of 7 Here is a layout I made for my DI before I switched to the Hammond. The black wire can connect to the Volume pot at pin 1. It's a pain to isolate standard metal switchcraft style 1/4" jacks.ĮDIT: it looks like the Jensen is different from the hammond I used. That's why you need to isolate the output jack from the chassis.ītw, get the plastic jacks. After you isolate the signal, you don't want that ground connection touching again. Since the transformer is mounted to the chassis, the left side of the schematic is grounded to the chassis. One of the secondary wires is playing the role of the ground, but isolated by the transformer. You're taking a balanced signal and turning it into an unbalanced signal. If you use a multimeter, you should read zero resistance between that wire and a metal part of the transformer. The ground wire is just a simple wire that connects to the transformers chassis. If the black wire is the ground wire, you don't want to connect it after the transformer. I do have a couple questions (found on the actual drawing also):ġ) Is the Ground Switch wire OK? The switch will be SPST toggle switch (BTW, there should read "Pin 1" in the picture's question section, NOT "Pin 3"!)Ģ) Since the impedance pot operates as a variable resistor, should the ground (terminal 1) be wired to the wiper/out (terminal 2) or vice versa?ģ) Could the Jack's ground wire be soldered to the Volume pot's ground terminal (1)?ĭoes everything look OK on the whole? (Exluding the clumsy penmanship, of course!) This is my first attempt to build straight from a schematic, and although this is considerably an easy build, I don't rank my knowledge too high. If someone who's a real pro could browse it through and gave further instructions, I would be highly thankful. I'll attach the actual schematic to the second post. I made a drawing of the "physical layout" (adorable hand drawn components and wires. This is my first post here, and my third DIY project in general, so try to be gentle.Īs the title states, I'm going to build the Jensen reamp box.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |